LIFTING, SECURITY |
| |
 |
Our systems designed to measure or control loads on lifting machinery are precise, reliable and designed to resist to the most difficult environments.
We propose three types of solutions:
Load pin
Load pins are installed to replace a traditional transmission spindle or shaft, and provide a very reliable means of measuring forces applied on the pin.
Tension-compression S type load cell
This S type load cell is complementary to the load pin, and is distinguished by its ease of use and high precision.
Extensometer
The extensometer must be fixed to the location of the maximum stress proportional to the force to be measured. We suggest Epsimetal, a miniature and repositionable extensometer, so that you can easily choose its optimum location.
|
|
 |
| |
 |
|
 |
|
 |
OVERLOAD CONTROL WITH LOAD PIN
 Measuring loads or controlling overloads on lifting equipment frequently requires the use of expensive equipment difficult to install.
The load pin provides an excellent solution that limits these modifications, because it consists simply of replacing by an instrumented load pin:
• an attachment pin
• a pulley shaft
• a lifting device
SCAIME load pins are used in load control for: 
cranes, pulley blocks, elevators, conveyors, winches, traveling cranes, vehicle structures, carriages and any other type of lifting equipment.
They can be used in severe environmental conditions such as tropical environments, marine or port installations. |
 |
 |
 |
 |
 |
 |
ZFA |
Nickel plated steel tension load cell |
25, 50, 100, 200, 500, 1 000, 2 500, 5 000 kg |
±0.03 % |
 |
SD25X |
Stainless steel tension load cell |
0.5, 1, 2, 4, 6 t |
C2.5 |
 |
MTRD |
Stainless steel tension load cell |
5, 10, 20, 30, 50 t |
±0.15 % |
 |
MTRS |
Stainless steel tension load cell |
5, 10, 20, 30, 50 |
±0.15 % |
 |
M15 |
Aluminum load pin |
20, 50, 100, 200 kg |
jusqu'à 0.1 % |
 |
M16 |
Stainless steel load pin |
0.5, 1, 2, 4, 5, 10, 20, 40, 60, 80, 100 t |
up to 0.1 % |
 |
ROD END ZFA |
Tension mounting for ZFA |
up to 2.5 t |
- |
 |
SD25X-BT |
Tension mounting for SD25X |
up to 6 t |
- |
 |
EPSIMETAL V |
Miniature strain sensor, 0-10 V or 4-20 mA output |
1 000 µm/m |
1% |
 |
CPJ / CPJ2S |
Strain gage conditioner |
outputs ±10 V, 0-10 V, 4-20 mA |
±0.05 % |
 |
IPE50 Panel |
Front panel weighing indicator |
LED 18 mm display |
10 000 d, OIML R76 |
 |
IPE50 DIN |
DIN rail housing weighing indicator |
LED 9 mm display |
10 000 d, OIML R76 |
 |
IPE50 XLR |
Large matrix weighing indicator - Repeater |
LED 60 mm display, wall mounting |
10 000 d, OIML R76 |
 |
PAX S |
Programmable indicator |
20 meas.s. |
0.02 % |
 |
ALCJB-A |
Junction box for analog load cells |
4, 6, 8 load cells, lightning protection |
- |
 |
Analog cable |
Connection cable for analog load cells |
6-wire shielded connection |
- |
 |
SYSTEX |
ATEX system certificate |
For ATEX measuring chain |
- |
 |
B15, B16, B19 |
ATEX Zener barriers kit |
for ATEX measuring chain |
- |
 |
Calibration kg |
Weighing calibration |
6 t in tension, 20 t in compression |
< ±0.02% |
|
|
